The PCM2002/CON Module implements the PCM controller function. All available PCM2002 series modules can be attached to the PCM2002/CON Base Module to perform local data acquisition. The PCM2002/CON Module can perform data acquisition in a stand-alone format or in a distributed network with multiple remote modules.

The PCM2002/RI Module implements the PCM remote function for distributed PCM configured systems. All available PCM2002 series modules can be attached to the PCM2002/RI Base Module to perform remote data acquisition.

The A/D Module performs 12 bit A/D conversion at speeds up to 5 Mega bits per second. The PCM2002/AD module provides 2 programmable gain amplifiers and one programmable offset generator. The PCM2002/AD module can work with signals up to 20 volts peak to peak (± 10 volts).

The 64 channel high level input module provides 64 channels of single ended analog multiplexing. The multiplexer can accept signals up to ± 10 volts with ± 30 volts overvoltage protection on each input. Output amplification provides gains from 1 to 4.

The 32 differential high level channel module provides 32 differential high level channels for analog inputs. The multiplexer can accept signals up to ± 10 volts with ± 30 volts overvoltage protection on each input. Output amplification provides gains from 1 to 4.

The 96 channel BI-Level input module provides 96 channels of single ended discrete multiplexing. The threshold of these inputs is TTL or CMOS. Each input is overvoltage protected to ± 75 volts.

The ITIMB Module provides IRIG B timing capability. The IRIG B electronics synchronizes with an external IRIG B input after the signal has been applied to the input for a maximum of 10 seconds. When the external signal is removed the unit will maintain IRIG Time consistent with the drift rate specifications of the internal oscillator. A reset time signal is available as an input.

The SE16F6 Module performs the multiplexing of 16 high level single ended analog inputs and provides 16 anti-alaising 6 pole low pass filters on each input. Filter frequencies are available from 5 Hz to 20 kHz. The module can be ordered with standard fixed gains of 1 or 4. Overvoltage protection of ± 30 volts on each input is provided.

The PMF-4 Module provides 4 Pre Modulation Filter outputs. The coding of each is programmable (NRZ-L, NRZ-M, NRZ-S, BIO-L, BIO-M, BIO-S, RNRZ-L.) The filter frequency cutoffs are fixed.

The TC-JKET Module is a very accurate 8 channel Thermocouple Conditioner with Reference Junction Compensation, Amplifier and Multiplexer Compensation, and Real Time Linearization. Linearization can be turned on or off. Each channel has an analog low pass filtered. Offset and amplification is programmable on a per channel basis for zoom and sliding range. Compatible with types J, K, E, and or T. The Reference Junction Block is separate from the PCM2002/TC-JKET conditioner module for ease of thermocouple connect, disconnect and reference junction temperature isolation.

The MIL-STD-1553 Bus Monitor Module implements IRIG-106-96, chapter 4 and or chapter 8 100% MIL-STD-1553 bus data acquisition. The messages are stored in a FIFO buffer. One Dual Redundant input channel is provided with direct or transformer coupling. For chapter 8 100% MIL-STD-1553 bus data acquisition with up to 8 dual redundant 1553 channels, use multiple PCM2002/1553 Modules stacked with a PCM2002/1553-OUT Module.

Provides PCM output and FIFO buffering for chapter 8 100% MIL-STD-1553 bus data acquisition. Use with one or multiple PCM2002/1553 Modules.

The FLASH-NV Module provides solid state recording for up to 5 Giga bytes of storage per module. Modules are stacked to increase recording time. Recorded data can be read back with the high-speed PCM2002/USB2-READ Module at up to 0.48 Giga bytes per second, or as serial PCM data (up to 5 Mega bit/sec) with clock, or as COM port data at 115.2 K Baud.

The USB2-READ Module provides high speed read back for solid state recording. The module uses the new USB2 specification to read large amounts of solid state data quickly. The module reads at data rates up to 0.48 Giga bits per second. Use with PCM2002/FLASH-NV Modules.

The BRG-VOL-2 Module provides 2 channels of bridge completion. Each channel has programmable gains from 1 to 2000. Each channel has programmable offset with 256 possibilities. Each channel has a programmable 6 pole low pass filter from 15 Hz to 3 kHz. Programmable Voltage Excitation is provided with current foldback limiting.

The CUR-2 Module provides 2 channels. Each channel has programmable gains from 1 to 2000. Each channel has programmable offset with 256 possibilities. Each channel has a programmable 6 pole low pass filter from 15 Hz to 3 kHz. Programmable Current Excitation is provided.